How to build a wood privacy fence

Lay out the fence line, set the posts in concrete, and attach the rails, pickets, and gate.

About 2 to 3 weekends Moderate

This guide covers a wood privacy fence built from individual rails and pickets. Allow time for utility marking before digging, for the concrete to cure before hanging the fence, and for the wood to dry before finishing it.

Start this project

Calculators for this job

Tools

  • Tape measure, stakes, and mason's string
  • Post-hole digger or power auger and shovel
  • Level and temporary braces
  • Saw, drill, and picket spacer
  • Wheelbarrow or mixing tub

Materials

  • Ground-contact rated posts
  • Gravel and post-setting concrete
  • Outdoor-rated wood rails and pickets
  • Galvanized or coated fasteners and gate hardware
  • Exterior stain or sealer

Steps

  1. Check the property line and rules

    Find the property line using your survey, not the old fence. If the line is unclear, have it marked by a surveyor. Check local height and setback rules, whether you need a permit, and whether your HOA requires approval.

  2. Call 811 before digging

    Contact 811 and wait for the utility locate request to clear before you dig. Follow the local rules for digging near the marks. Ask about a private locator for lines 811 may not mark, such as power to a shed or sprinkler lines.

  3. Mark the fence line and post locations

    Drive stakes at the corners and ends and pull a tight string between them. Mark the gate posts using the opening width required by your hinges and latch. Space the line posts evenly, usually 6 to 8 feet apart on center, or closer if your design or local rules call for it.

  4. Dig the post holes

    A common starting point is to bury about one third of the post's above-ground height, plus extra hole depth for the gravel base. For a post that stands 6 feet above ground, that's about 2 feet of buried post before allowing for gravel. Follow local frost-depth requirements and use deeper or wider holes if your soil or gate design calls for them.

  5. Set the posts in concrete

    Set corner, end, and gate posts first. Check each post with a level on two sides, brace it plumb, and add concrete as directed on the bag. Stretch a string between the set posts to line up the rest, and wait until the concrete can take the load before attaching rails or hanging the gate.

  6. Attach the rails

    Mark the rail heights on the posts and check them against the fence layout before fastening. Cut each rail to fit its opening and attach it with exterior fasteners rated for the wood. Check that neighboring rails line up as you go.

  7. Hang the pickets

    Stretch a string at the planned picket height. Set the first picket plumb, then use a spacer to keep the gaps even and check the tops against the string. Keep the bottom ends clear of the soil and check every few pickets with a level.

  8. Build and hang the gate

    Build a square frame sized to leave the clearances your hardware needs. Fit a solid diagonal wood brace from the lower hinge corner to the upper latch corner to help prevent sagging. With a helper, hang the gate, fit the latch, and check that it swings freely.

  9. Seal or stain the fence

    Wait until the wood is dry enough for the finish you chose, especially if the lumber was wet when you bought it. Clean the wood and apply an exterior stain or sealer as directed. Follow the label for drying time and the weather conditions you need.

Tips

  • Use posts labeled for ground contact, not lumber rated only for above-ground use.
  • Use galvanized or coated fasteners rated for outdoor use and compatible with your treated lumber.
  • Set the corner and gate posts first, then pull a tight string between the set posts to keep the line posts straight.
  • Slope the top of the concrete away from the post so rain doesn't pool against the wood.

Safety

  • Always call 811 before digging. Wait for clearance and obey the local rules around marked lines.
  • Wear gloves when handling rough lumber or mixing concrete, and safety glasses when cutting, drilling, or mixing.
  • Follow the power auger's instructions, keep loose clothing clear, and stop the machine before clearing a jam. Use the number of operators the maker specifies.
  • Get help lifting long posts, concrete bags, and the finished gate.

Estimates only. Check quantities with your supplier before you buy. © 2026 HouseCalcs