How to plan a roof replacement
See what goes into a new asphalt shingle roof, estimate materials, and compare roofer bids. Most homeowners hire this job out.
This guide covers planning and managing an asphalt shingle roof replacement, not doing the work yourself. Use the calculators to check rough quantities, then have your roofer confirm what the job needs.
Calculators for this job
Tools
- Tape measure for measurements from the ground
- House plans or a roofer's measurements
- Phone camera for photos from the ground
- Notebook or spreadsheet for comparing bids
Materials
- Asphalt shingles, starter strips, and ridge caps
- Roof underlayment and ice-and-water barrier where required
- Drip edge and flashing
- Attic intake and exhaust vents
- Replacement roof decking as needed
Steps
Look for signs the roof needs replacing
From the ground, look for missing or curling shingles, patches of bare shingle surface, or a sagging roofline. Indoors, look for new water stains on ceilings. Have a roofer check whether the damage is widespread or a repair would be enough.
Measure the house and find the pitch
Use house plans or measure the outside length and width in feet from the ground. Get the roof overhang in inches and ask the roofer to confirm the pitch. A 6/12 pitch means the roof rises 6 inches for every 12 inches across. Have the roofer measure roofs with additions or sections with different slopes.
Estimate squares, bundles, and underlayment
Enter the house dimensions, overhang, and pitch in the shingle and underlayment calculators. One roofing square covers 100 square feet. The shingle estimate assumes three bundles per square, but check the coverage on the product you choose. Ask the roofer to confirm waste, roll coverage, and quantities for valleys and other cuts.
Check the attic ventilation
Ask the roofer where fresh air comes in and where warm air goes out, and whether insulation blocks any intake vents. Use the roof vent calculator with the attic floor dimensions for a rough check. Have the roofer confirm the intake and exhaust sizes for your attic and local code.
Choose the shingles and color
Ask for the exact brand and product line so bids cover comparable shingles. Look at samples outside in daylight next to the siding or brick. Check any HOA color rules before ordering.
Get at least three written bids
Ask each roofer to list tear-off and disposal, decking repair price per sheet, underlayment, drip edge, flashing, ventilation, and cleanup. Check whether flashing will be replaced or reused and what is excluded. Compare the work listed, not just the total.
Check the license, insurance, and permit
Verify the roofer's license if your state or locality requires one. Ask for proof of current liability and workers' compensation coverage as applicable. Check with the local building department about permits and inspections, and put who handles them in the contract.
Know what happens on install day
The crew protects the area, tears off the old roof, and checks the exposed decking. Ask to see photos of any damaged decking before approving extra work. The crew makes approved repairs, installs the new roof and vents, then removes debris. Keep clear of the work area until the crew says it is safe.
Do a final walk-around
Walk the property with the roofer from the ground and ask for photos of the finished roof, flashing, and vents. Confirm cleanup and any required inspection. Keep the signed contract, final invoice, and written workmanship and manufacturer warranties, and check who handles warranty registration.
Tips
- Ask how rotten decking is priced before work starts and whether the price per sheet includes labor and disposal.
- Move cars out of the driveway before the crew arrives and keep pets indoors or away from the work area.
- Ask the roofer to run a magnetic sweep for nails around the driveway, walkways, and yard before leaving.
Safety
- Roof work is dangerous. Leave all work on the roof to insured professionals, including measuring or checking the finished job.
- Stay off ladders on wet or windy days. Use plans, ground measurements, or the roofer's photos instead of climbing to inspect the roof.
- Keep everyone clear of areas where shingles, nails, or tools could fall during the job.