How to plan a kitchen refresh
Update your kitchen on a budget with new countertops, a tile backsplash, recessed lights, and paint, without moving cabinets or plumbing.
Keep the cabinets and plumbing where they are. You can usually paint and set the backsplash yourself. Hire a countertop fabricator and use a licensed electrician where required. Most of the schedule is waiting for the countertops to be made.
Calculators for this job
Tools
- Tape measure and straightedge
- Drop cloths, painter's tape, and paint roller
- Level, notched trowel, and tile spacers
- Tile cutter or wet saw
- Grout float, sponge, and caulk gun
Materials
- Countertop material, sink, and faucet
- Recessed light fixtures approved for the space
- Primer and wall paint
- Backsplash tile, compatible mortar, and grout
- Flexible kitchen sealant
Steps
Set the budget
Start with Kitchen refresh in the Project Estimator. Enter counter sizes in feet and inches, the backsplash area, and your rough light count. Add quotes for fabrication, installation, wiring, and any sink hookup separately from your DIY materials. Leave room in the budget for surprises behind the old finishes.
Choose the countertop
Compare installed prices and care needs for laminate, solid surface, quartz, or stone. Ask what the quote covers, including removal, edges, cutouts, and disposal. Pick the sink and faucet before you book templating.
Plan the recessed lights
Sketch where you prep, cook, and wash up. Plan light over the work surfaces so you don't stand between the light and the counter. Ask the electrician to check the ceiling framing and what's above it before you settle on fixture locations.
Hire out the wiring
Have a licensed electrician wire the lights where required and handle any permits or inspections that apply. Get the lighting work done before the new counters go in so ceiling cuts and repairs don't put the new surface at risk.
Have the counters templated and installed
Hire the fabricator to measure the actual cabinets and make a template. Have the sink and faucet on hand so they can check the cutouts and clearances. Confirm when the old counters must come out, then have the fabricator install the new pieces. Arrange for the sink and faucet to be reconnected in their existing locations.
Paint the walls
Protect the new counters with a clean cover. Patch any damage, prime as needed, and paint the wall areas that will stay exposed before tiling. Keep the tile area clean and prepare it as directed by the mortar maker.
Set and grout the backsplash
Dry-lay a row and shift it if you get skinny cuts at the ends. Use a level guide and spacers to keep the rows even, and leave a small gap where the tile meets the counter. Set the tile in compatible mortar, let it set as directed, then grout the tile joints and wipe off the haze with a damp sponge.
Caulk the counter joint
Keep grout out of the gap where the backsplash meets the counter. Once the surfaces are clean and dry, fill that joint with a compatible flexible kitchen sealant. Let it cure as directed before getting it wet.
Clean up and check the work
Remove the covers, wipe the surfaces with cleaners approved for the new finishes, and save a few spare tiles. Check that the lights work and look for drips under the sink after running water and draining it.
Tips
- Do the lighting first, then the counters, then paint, then the backsplash. Get the fabrication lead time early so you can line up the other work.
- Order the sink and faucet before templating and confirm they've arrived. A late change can mean a new template or a costly cutout change.
- Set up a temporary kitchen with a table, dishes, and a place to wash up while the counters or sink are out of use.
Safety
- Turn off power at the breaker before any electrical work, even if the wall switch is off. Verify the circuit is off before working around outlets, and leave wiring to a licensed electrician where required.
- Cutting stone or tile can release silica dust. Leave stone cutting to the fabricator, wet-cut tile when appropriate, and use a properly fitted respirator rated for the dust. Don't dry-sweep the dust.
- Let the installers handle heavy countertop pieces. If you need to move one, don't lift it alone. Get help and use equipment rated for the load.